Sealing Tubular Sidewalls with Liquid Urethane

Those who have picked up tubulars have heard about sealing the sidewalls with AquaSeal, CX magazine had a tip using McNETT Tent Sure Urethane Sealant.  Tent Sure can be purchased at mec.ca for only $8.50; http://bit.ly/8dBJ9j

I found Aqua Seal to be somewhat thick (like honey) with application to be uneven.  I will be giving this a try instead.

The article to follow with the link to the orignal: http://bit.ly/6ZFyEJ 

Enjoy

Martin

 Gut-Wrenching Mechanical Mondays: Sealing Tubular Sidewalls with Liquid Urethane

November 30th, 2009

by Dave Drumm & Josh Liberles

While many tubular cyclocross tires have no need for the application of extra sealant (think of the rigid, robust sidewalls on a Tufo, for example), the more supple and sensitive sidewalls can benefit from extra protection from water absorption. For the ultra-supple, pricey tubulars that feature natural casings made from cotton or silk, like Dugasts and FMBs, some form of sealant is a necessity. Otherwise, get the tires wet often enough, and they’ll start to rot – not what you want to see from some of the most expensive ‘cross tires on the market.

Urethane on a Challenge (front) and one without (rear) © Dave Drumm

With a tubular like Challenge that has a very supple sidewall but has a poly casing, the tire is not in danger of rotting from moisture. However, an application of sealant will definitely keep the tires looking a whole lot better and will add longevity and protection from abrasions to your setup as well. See the photo of two Challenge setups above. Both wheels have similar miles on them.

Aqua Seal is probably the most typical sealant used for tubulars like these, but the trade-off has always been a compromise in the tire’s suppleness, which defeats a good chunk of the purpose of buying such tires. Not so with liquid urethane which goes on like paint, remains very flexible when dry and does not affect the suppleness of the tubular casing.

Dave’s Secret Sealant Tip:

Application in action - to a Dugast © Dave Drumm

Although many people swear by Aqua Seal, I prefer using a thinner, less shiny, easier to apply sealant like McNETT. McNETT Tent Sure Urethane Sealant, designed for tents as the name says, is available at most camping supply stores. An 8oz bottle will set you back around $10. Sealing your tires helps to prolong the life of your investment – let’s face it, tubular tires are not cheap. This is a very inexpensive and easy procedure that will ensure that your sidewalls last as long as the tread,  provided you don’t rip a large gaping hole in them  during a race.

The Process:

I recommend that you start on a NEW tubular that you have mounted. Wait until the you’ve completed the gluing process and the tire is fully set up before applying the liquid urethane.

Using a small foam brush, paint on a thin even coat of the liquid on the sidewall only. Cover the full sidewall from rim to tread. Try not to get the urethane on the rim – but if you do, don’t worry too much because it’s designed to bond to canvas, cotton and silk and doesn’t adhere well to rubber, carbon or aluminum.

Once you have applied a thin coat to both tire sidewalls, visually inspect the tire in a well-lit area to make sure you have not missed any spots. The urethane will have a slight sheen to it and it should be fairly easy to pick up on any spots that have not been coated. Once your sidewalls have a thin even coating, it’s time to let them cure. The curing process takes 24 hours. That means not riding them for at least a full day or all of your hard work will be in vain. The tire should be allowed to cure in a warm room; if you do work in an unheated or damp garage,  bring them inside to dry for the 24-hour period.

McNETT Urethane and tools of the trade © Dave Drumm

If you did get the sealant on the rim, remove it before using your newly sealed tires.  To remove excess sealant from the rim take a razor blade and LIGHTLY follow the curve of the tire where it intersects the rim in the offending area. This will cut the junction of Urethane between the rim and the tire allowing you to scrape the sealant from your braking surface without damaging the sealant that is on the tire sidewalls.  You can easily use you finger nail or rag to scrape the excess Urethane from the rim.

Once the rubber is dry and your braking surface is urethane-free,  you will have tires that will clean easily and look good after a hard weekend in the nastiest of conditions – just like Sven Nys!

Note that some tires, like Challenge’s new white Grifo and those in Vittoria’s entire tubular line,  offer coated sidewalls that offer similar benefits as sealant.